La slope 2x1 lisse et la 1x1 de coin :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/1x2cheeseslope.jpg_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/1x2cheeseslope2.jpg_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/cheeseslopecorner.jpg_thumb.jpg)
Des arrondis de finition :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/double_bow_1x2.jpg_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/brick_4x2_with_bow.jpg_thumb.jpg)
Des jumpers dont le 3x1 :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/1x3_plate_with_two_studs.png_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/1x3_plate_with_two_studs1.png_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/2x2jumperround.jpg_thumb.jpg)
Des wedge plates qui m'ont fait défaut par le passé :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/2x2-2x5.jpg_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/2x2wedges1.jpg_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/2x6wedges.jpg_thumb.jpg)
La plate ronde 3x3 :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/3x3round_plate.png_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/3x3round_plate1.png_thumb.jpg)
La brique octogonal 1x1 (et il faudrait aussi une 2x2) et la plate octogonale 4x4 :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/octogonal_brick_1x1.png_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/octogonal_brick_1x11.png_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/wedge_plate_4x4_cut_corners.jpg_thumb.jpg)
Celle-là, je me demande pourquoi elle n'existe pas vu qu'il existe celle-là
![Image](http://img.bricklink.com/P/86/14418.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/plate1x2withballside.jpg_thumb.jpg)
Des briques 2x1 et 2x2 pour le SNOT :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/plate1x2x2_with_2_knobs_on_each_side.jpg_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/brick_1x2x2_with_four_knobs1.jpg_thumb.jpg)
Une brique pour un joli raccord carré-rond :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/brick_2x2_with_round_top.jpg_thumb.jpg)
Et des barres technic avec des trous à 90° :
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/beam_3_l_with_perpendicular_holes.jpg_thumb.jpg)
![Image](http://www.brickshelf.com/gallery/Bio-Brothers/Custom-Parts/thumb/beam_15_l_with_perpendicular_holes.jpg_thumb.jpg)
Qu'en pensez-vous ?